Oct 01 2025 12:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 01 2025 12:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 01 2025 12:00:09 orcad: startLoggingCTD19Plus(): Failed sending first INITLOGGING command ( retries = 0 ). Oct 01 2025 12:00:10 orcad: startLoggingCTD19Plus(): Failed sending OUTPUTFORMAT=3 command after two attempts. Oct 01 2025 12:00:10 orcad: profile(): Failed to activate the CTD! Oct 01 2025 12:00:10 orcad: runJobs(): Mission Deep_Cast_Direct profile returned: -2 Oct 01 2025 12:00:12 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 01 2025 14:03:46 orcad: cleanup(): Caught exit signal ( 15 )! Attempting to shutdown cleanly... Oct 01 2025 14:03:46 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 01 2025 14:24:28 orcad: Starting up ( version 0.9.17_test )... GLOBAL PARAMETERS ----------------- isDaemon = 0 debugLevel = 4 configFileName = /usr/local/orcaD/orcad.cfg min_depth = 2 max_depth = 105 parking_depth = 20 data_file_prefix = ORCA2_CAST data_storage_dir = /usr/local/orcaD/data last_cast_num = 25140 weather_data_prefix = ORCA2_MET weather_archive_download_period = 1440 weather_status_filename = weather-status.dat ctd_cal_PA1 = 2.482456e+02 ctd_cal_PA2 = -6.524518e-02 ctd_cal_PA3 = 5.430179e-08 solar_calibration_constant = 6.490000e+00 INFO: Assuming Licor 2420 Light Sensor Amplifier with 0.150 gain compass_declination = 1.600000e+01 meterwheel_cfactor = 1.660000e-01 SERIAL DEVICES -------------- RS232 Port description = A happy little CTD device_type = SEABIRD_CTD_19_PLUS tty = /dev/ttyUSB1 baud = 9600 stop_bits = 1 data_bits = 8 flow_control = none parity = none RS232 Port description = A happy little WeatherStation device_type = GILLMETPAK tty = /dev/ttyUSB2 baud = 19200 stop_bits = 1 data_bits = 8 flow_control = none parity = none RS232 Port description = A happy little WeatherStation device_type = S9VAISALA tty = /dev/ttyUSB3 baud = 19200 stop_bits = 1 data_bits = 8 flow_control = none parity = none MISSIONS -------- name = Deep_Cast_Direct start_min = 0 start_hour = 0,12 start_day_of_month = * start_month = * start_day_of_week = * equilibration_time = 20 aux_sample_direction = down cycles = 1.0 depths = Oct 02 2025 00:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 02 2025 00:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 02 2025 00:00:12 orcad: profile(): pres= 20.73db prdp= 20.55m mwdp= 0.0 ipwr=13.6v epwr=26.2v Oct 02 2025 00:03:10 orcad: movePackageUp(): pressureDepth = 2.863903; Pm1(recent)-4(older) = 3.031491, 3.191147, 3.349810, 3.511449 Oct 02 2025 00:03:11 orcad: profile(): pres= 2.51db prdp= 2.49m mwdp= 0.0 ipwr=13.6v epwr=26.0v il_f=0.00a Oct 02 2025 00:08:53 orcad: profile(): pres=105.26db prdp=104.36m mwdp= 0.0 ipwr=13.6v epwr=26.2v il_f=0.00a Oct 02 2025 00:14:22 orcad: movePackageUp(): pressureDepth = 20.883356; Pm1(recent)-4(older) = 21.033082, 21.178841, 21.330550, 21.478292 Oct 02 2025 00:14:24 orcad: profile(): pres= 20.72db prdp= 20.54m mwdp= 0.0 ipwr=13.6v epwr=26.0v il_f=0.00a Oct 02 2025 00:14:26 orcad: runJobs(): Creating /usr/local/orcaD/data/202510/ORCA2_CAST25141.HEX Oct 02 2025 00:17:14 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 02 2025 12:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 02 2025 12:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 02 2025 12:00:12 orcad: profile(): pres= 20.72db prdp= 20.54m mwdp= 0.0 ipwr=13.4v epwr=26.6v Oct 02 2025 12:03:08 orcad: movePackageUp(): pressureDepth = 2.782587; Pm1(recent)-4(older) = 3.054299, 3.229821, 3.396418, 3.564006 Oct 02 2025 12:03:09 orcad: profile(): pres= 2.42db prdp= 2.40m mwdp= 0.0 ipwr=13.4v epwr=26.4v il_f=0.00a Oct 02 2025 12:08:42 orcad: profile(): pres=105.34db prdp=104.43m mwdp= 0.0 ipwr=13.6v epwr=26.6v il_f=0.00a Oct 02 2025 12:13:58 orcad: movePackageUp(): pressureDepth = 20.863525; Pm1(recent)-4(older) = 21.022175, 21.172892, 21.324601, 21.566541 Oct 02 2025 12:13:59 orcad: profile(): pres= 20.67db prdp= 20.50m mwdp= 0.0 ipwr=13.4v epwr=26.3v il_f=0.00a Oct 02 2025 12:14:01 orcad: runJobs(): Creating /usr/local/orcaD/data/202510/ORCA2_CAST25142.HEX Oct 02 2025 12:16:45 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 03 2025 00:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 03 2025 00:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 03 2025 00:00:09 orcad: startLoggingCTD19Plus(): Failed sending confirmation INITLOGGING command ( retries = 0 ). Oct 03 2025 00:00:11 orcad: startLoggingCTD19Plus(): Failed sending confirmation INITLOGGING command ( retries = 1 ). Oct 03 2025 00:00:14 orcad: startLoggingCTD19Plus(): Failed sending first INITLOGGING command ( retries = 2 ). Oct 03 2025 00:00:15 orcad: startLoggingCTD19Plus(): Failed sending confirmation INITLOGGING command ( retries = 2 ). Oct 03 2025 00:00:15 orcad: startLoggingCTD19Plus(): Failed to issue INITLOGGING command to CTD after 3 retries. Oct 03 2025 00:00:15 orcad: profile(): Failed to activate the CTD! Oct 03 2025 00:00:15 orcad: runJobs(): Mission Deep_Cast_Direct profile returned: -2 Oct 03 2025 00:00:17 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 03 2025 12:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 03 2025 12:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 03 2025 12:00:10 orcad: startLoggingCTD19Plus(): Failed sending OUTPUTFORMAT=3 command after two attempts. Oct 03 2025 12:00:10 orcad: profile(): Failed to activate the CTD! Oct 03 2025 12:00:10 orcad: runJobs(): Mission Deep_Cast_Direct profile returned: -2 Oct 03 2025 12:00:13 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 03 2025 12:01:37 orcad: cleanup(): Caught exit signal ( 15 )! Attempting to shutdown cleanly... Oct 03 2025 12:01:37 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:28:16 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:28:20 orcad: initCTD19Plus(): Failed to send MP command. Oct 03 2025 12:28:20 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:28:20 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:28:20 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:28:20 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:28:20 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:28:23 orcad: initCTD19Plus(): Failed to send 2nd MP command. Oct 03 2025 12:28:23 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:28:23 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:28:23 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:28:23 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:28:23 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:28:25 orcad: initCTD19Plus(): Failed to send MP command. Oct 03 2025 12:28:25 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:28:25 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:28:25 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:28:25 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:28:26 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:28:28 orcad: initCTD19Plus(): Failed to send 2nd MP command. Oct 03 2025 12:28:28 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:28:28 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:28:28 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:28:28 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:28:29 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:28:31 orcad: initCTD19Plus(): Failed to send MP command. Oct 03 2025 12:28:31 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:28:31 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:28:31 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:28:31 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:28:31 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:28:34 orcad: initCTD19Plus(): Failed to send MP command. Oct 03 2025 12:28:34 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:28:34 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:28:34 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:28:34 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:28:34 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:28:36 orcad: initCTD19Plus(): Failed to send MP command. Oct 03 2025 12:28:36 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:28:36 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:28:36 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:28:37 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:28:37 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:28:41 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Oct 03 2025 12:28:41 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:28:41 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:28:41 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:28:41 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:28:41 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:28:45 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Oct 03 2025 12:28:45 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:28:45 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:28:45 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:28:45 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:28:46 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:28:48 orcad: initCTD19Plus(): Failed to send MP command. Oct 03 2025 12:28:48 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:28:48 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:28:48 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:28:48 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:28:48 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:28:55 orcad: initCTD19Plus(): Could not set OUTPUTFORMAT=3 two attempts. Oct 03 2025 12:28:55 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:28:55 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:28:55 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:28:55 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:28:55 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:28:59 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Oct 03 2025 12:28:59 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:28:59 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:28:59 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:28:59 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:29:00 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:29:02 orcad: initCTD19Plus(): Failed to send 2nd MP command. Oct 03 2025 12:29:02 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:29:02 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:29:02 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:29:02 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:29:02 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:29:05 orcad: initCTD19Plus(): Failed to send 2nd MP command. Oct 03 2025 12:29:05 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:29:05 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:29:05 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:29:05 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:29:05 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:29:09 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Oct 03 2025 12:29:09 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:29:09 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:29:09 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:29:09 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:29:09 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:29:13 orcad: initCTD19Plus(): Could not set AUTORUN=n after two attempts. Oct 03 2025 12:29:13 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:29:13 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:29:13 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:29:13 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:29:14 orcad: Starting up ( version 0.9.17_test )... Oct 03 2025 12:29:19 orcad: initCTD19Plus(): Could not set AUTORUN=n after two attempts. Oct 03 2025 12:29:19 orcad: intializeHardware(): Could not initialize the hydro device! Oct 03 2025 12:29:19 orcad: main(): Could not initialize the hardware! Oct 03 2025 12:29:19 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Oct 03 2025 12:29:19 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Oct 03 2025 12:29:19 orcad: Starting up ( version 0.9.17_test )... GLOBAL PARAMETERS ----------------- isDaemon = 0 debugLevel = 4 configFileName = /usr/local/orcaD/orcad.cfg min_depth = 2 max_depth = 105 parking_depth = 20 data_file_prefix = ORCA2_CAST data_storage_dir = /usr/local/orcaD/data last_cast_num = 25143 weather_data_prefix = ORCA2_MET weather_archive_download_period = 1440 weather_status_filename = weather-status.dat ctd_cal_PA1 = 2.482456e+02 ctd_cal_PA2 = -6.524518e-02 ctd_cal_PA3 = 5.430179e-08 solar_calibration_constant = 6.490000e+00 INFO: Assuming Licor 2420 Light Sensor Amplifier with 0.150 gain compass_declination = 1.600000e+01 meterwheel_cfactor = 1.660000e-01 SERIAL DEVICES -------------- RS232 Port description = A happy little CTD device_type = SEABIRD_CTD_19_PLUS tty = /dev/ttyUSB1 baud = 9600 stop_bits = 1 data_bits = 8 flow_control = none parity = none RS232 Port description = A happy little WeatherStation device_type = GILLMETPAK tty = /dev/ttyUSB2 baud = 19200 stop_bits = 1 data_bits = 8 flow_control = none parity = none RS232 Port description = A happy little WeatherStation device_type = S9VAISALA tty = /dev/ttyUSB3 baud = 19200 stop_bits = 1 data_bits = 8 flow_control = none parity = none MISSIONS -------- name = Deep_Cast_Direct start_min = 0 start_hour = 0,12 start_day_of_month = * start_month = * start_day_of_week = * equilibration_time = 20 aux_sample_direction = down cycles = 1.0 depths = Oct 04 2025 00:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 04 2025 00:00:07 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 04 2025 00:00:13 orcad: profile(): pres= 20.66db prdp= 20.49m mwdp= 0.0 ipwr=13.6v epwr=26.2v Oct 04 2025 00:03:11 orcad: movePackageUp(): pressureDepth = 2.920427; Pm1(recent)-4(older) = 3.086032, 3.252629, 3.493599, 3.654246 Oct 04 2025 00:03:13 orcad: profile(): pres= 2.57db prdp= 2.55m mwdp= 0.0 ipwr=13.6v epwr=26.0v il_f=0.00a Oct 04 2025 00:08:57 orcad: profile(): pres=105.27db prdp=104.36m mwdp= 0.0 ipwr=13.6v epwr=26.1v il_f=0.00a Oct 04 2025 00:14:31 orcad: movePackageUp(): pressureDepth = 20.866500; Pm1(recent)-4(older) = 21.013251, 21.156035, 21.302786, 21.446562 Oct 04 2025 00:14:32 orcad: profile(): pres= 20.70db prdp= 20.53m mwdp= 0.0 ipwr=13.6v epwr=25.9v il_f=0.00a Oct 04 2025 00:14:35 orcad: runJobs(): Creating /usr/local/orcaD/data/202510/ORCA2_CAST25144.HEX Oct 04 2025 00:17:24 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 04 2025 12:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 04 2025 12:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 04 2025 12:00:12 orcad: profile(): pres= 20.67db prdp= 20.50m mwdp= 0.0 ipwr=13.4v epwr=26.5v Oct 04 2025 12:03:07 orcad: movePackageUp(): pressureDepth = 2.914477; Pm1(recent)-4(older) = 3.085040, 3.252629, 3.424184, 3.595738 Oct 04 2025 12:03:09 orcad: profile(): pres= 2.55db prdp= 2.53m mwdp= 0.0 ipwr=13.4v epwr=26.4v il_f=0.00a Oct 04 2025 12:08:35 orcad: profile(): pres=105.32db prdp=104.41m mwdp= 0.0 ipwr=13.4v epwr=26.5v il_f=0.00a Oct 04 2025 12:13:47 orcad: movePackageUp(): pressureDepth = 20.925002; Pm1(recent)-4(older) = 21.087618, 21.247259, 21.411858, 21.572490 Oct 04 2025 12:13:49 orcad: profile(): pres= 20.73db prdp= 20.56m mwdp= 0.0 ipwr=13.4v epwr=26.4v il_f=0.00a Oct 04 2025 12:13:51 orcad: runJobs(): Creating /usr/local/orcaD/data/202510/ORCA2_CAST25145.HEX Oct 04 2025 12:16:33 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 05 2025 00:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 05 2025 00:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 05 2025 00:00:12 orcad: profile(): pres= 20.70db prdp= 20.53m mwdp= 0.0 ipwr=13.6v epwr=26.2v Oct 05 2025 00:03:11 orcad: movePackageUp(): pressureDepth = 2.847045; Pm1(recent)-4(older) = 3.007692, 3.166355, 3.327994, 3.490624 Oct 05 2025 00:03:13 orcad: profile(): pres= 2.50db prdp= 2.48m mwdp= 0.0 ipwr=13.6v epwr=26.0v il_f=0.00a Oct 05 2025 00:08:59 orcad: profile(): pres=105.34db prdp=104.43m mwdp= 0.0 ipwr=13.6v epwr=26.1v il_f=0.00a Oct 05 2025 00:14:35 orcad: movePackageUp(): pressureDepth = 20.888314; Pm1(recent)-4(older) = 21.034073, 21.187765, 21.342449, 21.490191 Oct 05 2025 00:14:36 orcad: profile(): pres= 20.73db prdp= 20.56m mwdp= 0.0 ipwr=13.6v epwr=26.0v il_f=0.00a Oct 05 2025 00:14:38 orcad: runJobs(): Creating /usr/local/orcaD/data/202510/ORCA2_CAST25146.HEX Oct 05 2025 00:17:28 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 05 2025 12:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 05 2025 12:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 05 2025 12:00:12 orcad: profile(): pres= 20.73db prdp= 20.55m mwdp= 0.0 ipwr=13.4v epwr=26.6v Oct 05 2025 12:03:08 orcad: movePackageUp(): pressureDepth = 2.999759; Pm1(recent)-4(older) = 3.167347, 3.328986, 3.653254, 3.819850 Oct 05 2025 12:03:09 orcad: profile(): pres= 2.65db prdp= 2.62m mwdp= 0.0 ipwr=13.4v epwr=26.6v il_f=0.00a Oct 05 2025 12:08:36 orcad: profile(): pres=105.29db prdp=104.38m mwdp= 0.0 ipwr=13.4v epwr=26.5v il_f=0.00a Oct 05 2025 12:13:45 orcad: movePackageUp(): pressureDepth = 20.970614; Pm1(recent)-4(older) = 21.122322, 21.291879, 21.458461, 21.609178 Oct 05 2025 12:13:46 orcad: profile(): pres= 20.79db prdp= 20.61m mwdp= 0.0 ipwr=13.4v epwr=26.6v il_f=0.00a Oct 05 2025 12:13:48 orcad: runJobs(): Creating /usr/local/orcaD/data/202510/ORCA2_CAST25147.HEX Oct 05 2025 12:16:30 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 06 2025 00:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 06 2025 00:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 06 2025 00:00:12 orcad: profile(): pres= 20.75db prdp= 20.58m mwdp= 0.0 ipwr=13.6v epwr=26.2v Oct 06 2025 00:03:13 orcad: movePackageUp(): pressureDepth = 2.981909; Pm1(recent)-4(older) = 3.135614, 3.283370, 3.430134, 3.582847 Oct 06 2025 00:03:14 orcad: profile(): pres= 2.65db prdp= 2.63m mwdp= 0.0 ipwr=13.6v epwr=26.0v il_f=0.00a Oct 06 2025 00:09:00 orcad: profile(): pres=105.30db prdp=104.40m mwdp= 0.0 ipwr=13.6v epwr=26.1v il_f=0.00a Oct 06 2025 00:14:33 orcad: movePackageUp(): pressureDepth = 20.934917; Pm1(recent)-4(older) = 21.087618, 21.240318, 21.389052, 21.538777 Oct 06 2025 00:14:35 orcad: profile(): pres= 20.77db prdp= 20.60m mwdp= 0.0 ipwr=13.6v epwr=26.0v il_f=0.00a Oct 06 2025 00:14:37 orcad: runJobs(): Creating /usr/local/orcaD/data/202510/ORCA2_CAST25148.HEX Oct 06 2025 00:17:27 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 06 2025 12:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 06 2025 12:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 06 2025 12:00:12 orcad: profile(): pres= 20.75db prdp= 20.58m mwdp= 0.0 ipwr=13.4v epwr=26.8v Oct 06 2025 12:03:08 orcad: movePackageUp(): pressureDepth = 2.875802; Pm1(recent)-4(older) = 3.061241, 3.220896, 3.379560, 3.562022 Oct 06 2025 12:03:09 orcad: profile(): pres= 2.52db prdp= 2.50m mwdp= 0.0 ipwr=13.5v epwr=26.8v il_f=0.00a Oct 06 2025 12:08:32 orcad: profile(): pres=105.36db prdp=104.45m mwdp= 0.0 ipwr=13.4v epwr=26.6v il_f=0.00a Oct 06 2025 12:13:44 orcad: movePackageUp(): pressureDepth = 20.895255; Pm1(recent)-4(older) = 21.035065, 21.192723, 21.362280, 21.511014 Oct 06 2025 12:13:47 orcad: profile(): pres= 20.69db prdp= 20.52m mwdp= 0.0 ipwr=13.5v epwr=26.6v il_f=0.00a Oct 06 2025 12:13:49 orcad: runJobs(): Creating /usr/local/orcaD/data/202510/ORCA2_CAST25149.HEX Oct 06 2025 12:16:33 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 07 2025 00:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 07 2025 00:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 07 2025 00:00:12 orcad: profile(): pres= 20.65db prdp= 20.48m mwdp= 0.0 ipwr=13.7v epwr=26.3v Oct 07 2025 00:03:11 orcad: movePackageUp(): pressureDepth = 2.999759; Pm1(recent)-4(older) = 3.157431, 3.312128, 3.468808, 3.625488 Oct 07 2025 00:03:13 orcad: profile(): pres= 2.67db prdp= 2.65m mwdp= 0.0 ipwr=13.7v epwr=26.0v il_f=0.00a Oct 07 2025 00:09:00 orcad: profile(): pres=105.30db prdp=104.39m mwdp= 0.0 ipwr=13.7v epwr=26.1v il_f=0.00a Oct 07 2025 00:14:36 orcad: movePackageUp(): pressureDepth = 20.890297; Pm1(recent)-4(older) = 21.033082, 21.179833, 21.327575, 21.542744 Oct 07 2025 00:14:38 orcad: profile(): pres= 20.74db prdp= 20.56m mwdp= 0.0 ipwr=13.7v epwr=25.9v il_f=0.00a Oct 07 2025 00:14:40 orcad: runJobs(): Creating /usr/local/orcaD/data/202510/ORCA2_CAST25150.HEX Oct 07 2025 00:17:30 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 07 2025 12:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 07 2025 12:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 07 2025 12:00:12 orcad: profile(): pres= 20.65db prdp= 20.48m mwdp= 0.0 ipwr=13.4v epwr=26.7v Oct 07 2025 12:03:08 orcad: movePackageUp(): pressureDepth = 2.836137; Pm1(recent)-4(older) = 3.006700, 3.173297, 3.337910, 3.510457 Oct 07 2025 12:03:10 orcad: profile(): pres= 2.48db prdp= 2.46m mwdp= 0.0 ipwr=13.4v epwr=26.6v il_f=0.00a Oct 07 2025 12:08:39 orcad: profile(): pres=105.36db prdp=104.45m mwdp= 0.0 ipwr=13.4v epwr=26.6v il_f=0.00a Oct 07 2025 12:13:51 orcad: movePackageUp(): pressureDepth = 20.980529; Pm1(recent)-4(older) = 21.139179, 21.298820, 21.461436, 21.630001 Oct 07 2025 12:13:52 orcad: profile(): pres= 20.80db prdp= 20.63m mwdp= 0.0 ipwr=13.4v epwr=26.6v il_f=0.00a Oct 07 2025 12:13:54 orcad: runJobs(): Creating /usr/local/orcaD/data/202510/ORCA2_CAST25151.HEX Oct 07 2025 12:16:37 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 08 2025 00:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 08 2025 00:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 08 2025 00:00:12 orcad: profile(): pres= 20.75db prdp= 20.58m mwdp= 0.0 ipwr=13.7v epwr=26.3v Oct 08 2025 00:03:12 orcad: movePackageUp(): pressureDepth = 2.941251; Pm1(recent)-4(older) = 3.093965, 3.263537, 3.426167, 3.579872 Oct 08 2025 00:03:13 orcad: profile(): pres= 2.60db prdp= 2.58m mwdp= 0.0 ipwr=13.7v epwr=26.0v il_f=0.00a Oct 08 2025 00:08:55 orcad: profile(): pres=105.29db prdp=104.39m mwdp= 0.0 ipwr=13.7v epwr=26.1v il_f=0.00a Oct 08 2025 00:14:24 orcad: movePackageUp(): pressureDepth = 20.926985; Pm1(recent)-4(older) = 21.061837, 21.216521, 21.374179, 21.525887 Oct 08 2025 00:14:26 orcad: profile(): pres= 20.69db prdp= 20.51m mwdp= 0.0 ipwr=13.7v epwr=25.9v il_f=0.00a Oct 08 2025 00:14:28 orcad: runJobs(): Creating /usr/local/orcaD/data/202510/ORCA2_CAST25152.HEX Oct 08 2025 00:17:16 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 08 2025 12:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 08 2025 12:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 08 2025 12:00:12 orcad: profile(): pres= 20.66db prdp= 20.49m mwdp= 0.0 ipwr=13.5v epwr=26.3v Oct 08 2025 12:03:11 orcad: movePackageUp(): pressureDepth = 2.952159; Pm1(recent)-4(older) = 3.107848, 3.268495, 3.429142, 3.585822 Oct 08 2025 12:03:13 orcad: profile(): pres= 2.63db prdp= 2.61m mwdp= 0.0 ipwr=13.5v epwr=26.0v il_f=0.00a Oct 08 2025 12:08:54 orcad: profile(): pres=105.26db prdp=104.35m mwdp= 0.0 ipwr=13.5v epwr=26.0v il_f=0.00a Oct 08 2025 12:14:24 orcad: movePackageUp(): pressureDepth = 20.958715; Pm1(recent)-4(older) = 21.113398, 21.258166, 21.406900, 21.554642 Oct 08 2025 12:14:26 orcad: profile(): pres= 20.79db prdp= 20.62m mwdp= 0.0 ipwr=13.5v epwr=25.9v il_f=0.00a Oct 08 2025 12:14:28 orcad: runJobs(): Creating /usr/local/orcaD/data/202510/ORCA2_CAST25153.HEX Oct 08 2025 12:17:16 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 09 2025 00:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 09 2025 00:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 09 2025 00:00:12 orcad: profile(): pres= 20.76db prdp= 20.59m mwdp= 0.0 ipwr=13.7v epwr=26.3v Oct 09 2025 00:03:13 orcad: movePackageUp(): pressureDepth = 2.951168; Pm1(recent)-4(older) = 3.112806, 3.262545, 3.414267, 3.578880 Oct 09 2025 00:03:14 orcad: profile(): pres= 2.62db prdp= 2.59m mwdp= 0.0 ipwr=13.7v epwr=26.0v il_f=0.00a Oct 09 2025 00:09:00 orcad: profile(): pres=105.27db prdp=104.36m mwdp= 0.0 ipwr=13.7v epwr=26.0v il_f=0.00a Oct 09 2025 00:14:31 orcad: movePackageUp(): pressureDepth = 20.994411; Pm1(recent)-4(older) = 21.143145, 21.294854, 21.434664, 21.577448 Oct 09 2025 00:14:32 orcad: profile(): pres= 20.84db prdp= 20.66m mwdp= 0.0 ipwr=13.7v epwr=25.9v il_f=0.00a Oct 09 2025 00:14:35 orcad: runJobs(): Creating /usr/local/orcaD/data/202510/ORCA2_CAST25154.HEX Oct 09 2025 00:17:27 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 09 2025 12:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 09 2025 12:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 09 2025 12:00:12 orcad: profile(): pres= 20.88db prdp= 20.70m mwdp= 0.0 ipwr=13.4v epwr=26.3v Oct 09 2025 12:03:12 orcad: movePackageUp(): pressureDepth = 2.995792; Pm1(recent)-4(older) = 3.156439, 3.312128, 3.551114, 3.711761 Oct 09 2025 12:03:13 orcad: profile(): pres= 2.65db prdp= 2.63m mwdp= 0.0 ipwr=13.5v epwr=25.9v il_f=0.00a Oct 09 2025 12:08:54 orcad: profile(): pres=105.23db prdp=104.32m mwdp= 0.0 ipwr=13.6v epwr=26.1v il_f=0.00a Oct 09 2025 12:14:21 orcad: movePackageUp(): pressureDepth = 20.891289; Pm1(recent)-4(older) = 21.037048, 21.182808, 21.327575, 21.464410 Oct 09 2025 12:14:23 orcad: profile(): pres= 20.73db prdp= 20.56m mwdp= 0.0 ipwr=13.6v epwr=26.0v il_f=0.00a Oct 09 2025 12:14:25 orcad: runJobs(): Creating /usr/local/orcaD/data/202510/ORCA2_CAST25155.HEX Oct 09 2025 12:17:13 orcad: runJobs(): Completed mission: Deep_Cast_Direct Oct 10 2025 00:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Oct 10 2025 00:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Oct 10 2025 00:00:07 orcad: profile(): volt low - using i2c backup 26.4v Oct 10 2025 00:00:13 orcad: profile(): pres= 20.66db prdp= 20.48m mwdp= 0.0 ipwr=13.7v epwr=26.4v Oct 10 2025 00:03:12 orcad: movePackageUp(): pressureDepth = 2.996784; Pm1(recent)-4(older) = 3.157431, 3.317086, 3.467816, 3.692920 Oct 10 2025 00:03:13 orcad: profile(): pres= 2.68db prdp= 2.66m mwdp= 0.0 ipwr=13.7v epwr=26.1v il_f=0.00a Oct 10 2025 00:08:57 orcad: profile(): pres=105.23db prdp=104.33m mwdp= 0.0 ipwr=13.7v epwr=26.2v il_f=0.00a Oct 10 2025 00:14:33 orcad: movePackageUp(): pressureDepth = 20.877407; Pm1(recent)-4(older) = 21.019200, 21.158019, 21.294854, 21.498123 Oct 10 2025 00:14:34 orcad: profile(): pres= 20.73db prdp= 20.55m mwdp= 0.0 ipwr=13.7v epwr=25.9v il_f=0.00a Oct 10 2025 00:14:37 orcad: runJobs(): Creating /usr/local/orcaD/data/202510/ORCA2_CAST25156.HEX Oct 10 2025 00:17:26 orcad: runJobs(): Completed mission: Deep_Cast_Direct